Rancang Bangun Mesin Pencetak Bakso
Abstract
This research to design a smaller and easy to operate meatball maker machine. This design will simplify, speed up and minimize the energy expended in the meatball maker machine. Simulation of frame strength using Solidwork 2018. The simulation value of von Mises stress on the frame is with a maximum stress of 10,550,430.00 N/m2 and a minimum of 90,629 N/m2 with a yield strength of 250,000,000.00 N/m2. Displacement in the simulation of displacement is with a maximum value of 0.154 mm and a minimum of 0.000 mm. The value of the safety factor from the simulation results is 24. Static simulation results of the strength of the meatball printing machine frame using ASTM A36 Steel L 30 mm x 30 mm 3 mm thick with a load of 25 kg, the frame is able to withstand engine performance during operation.
References
I. P. Putri and Romiyadi, “Perancangan dan Pembuatan Mesin Penggiling Daging dan Pengaduk Adonan Bakso,” J. Tek. Mesin, vol. 7, no. 1, pp. 14–19, 2017.
A. Y. Aminy, “Rancang Bangun Mesin Pencetak Bakso,” Proceeding Semin. Nas. Tah. Tek. Mesin XII (SNTTM XII), 2013.
A. Tangkemanda, M. Iswar, A. Pongtandi, and R. L. Kastanya, “Rancang Bangun Mesin Pencetak Bakso Berskala Industri Rumah Tangga,” J. Sinergi Jur. Tek. Mesin, 2019, doi: 10.31963/sinergi.v15i2.1191.
Denny R. Pattiapon, Jacob J. Rikumahu, Marselin Jamlaay. 2019. Penggunaan Motor Sinkron Tiga Phasa Tipe Salient Pole Sebagai Generator Sinkron. Jurnal simetrik vol.9, no.2, desember 2019.
Sularso, & Suga, K. (2008). Dasar Perencanaan dan Pemilihan Elemen Mesin. Cetakan 12. PT Pradaya Paramita. Jakarta.
T. Nasution, Modul 1 Material Baja Sebagai Bahan Struktur. 2011
F. A. Budiman, A. Septiyanto, S. Sudiyono, A. D. N. I. Musyono, and R. Setiadi, “Analisis Tegangan von Mises dan Safety Factor pada Chassis Kendaraan Listrik Tipe In-Wheel,” J. Rekayasa Mesin, vol. 16, no. 1, p. 100, 2021, doi: 10.32497/jrm.v16i1.1997.
A. A. Kharisma and M. E. Marsaoly, “Analisis Kegagalan Pada Rangka Mesin Perontok Padi Kapasitas 1 Ton / Jam Menggunakan Metode Von Misses,” vol. 20, no. 2, pp. 13–18, 2020
I. Setiawan and Jumari, “Perencanaan kontruksi mesin penggiling dengan sistem roda gigi,” pp. 1–11, 2007.
E. Prasetyo, R. Hermawan, M. N. I. Ridho, I. I. Hajar, H. Hariri, and E. A. Pane, “Analisis Kekuatan Rangka Pada Mesin Transverse Ducting Flange (TDF) Menggunakan Software Solidworks,” Rekayasa, vol. 13, no. 3, pp. 299–306, 2020, doi: 10.21107/rekayasa.v13i3.8872.
